Question Info on Kuryk engine chrome kit - Page 2


Page 2 of 2 FirstFirst 12
Results 11 to 20 of 20

Thread: Info on Kuryk engine chrome kit

  1. #11
    Wizza's Avatar
    Wizza is offline Official Fuddy Duddy

    North Carolina Riders Group
    Join Date
    Oct 2007
    Location
    Jax
    Posts
    1,654
    The threaded rod was the most difficult part except for the triangle that fits in between the exhaust ....they take some patience for installation but the results are worth it.

  2. #12
    Join Date
    Jul 2007
    Location
    Southern
    Posts
    126
    Hey...........now I am interested too. MORE CHROME!!!!!!!!!!

  3. #13
    Join Date
    May 2009
    Location
    Saint Joseph
    Posts
    69
    Quote Originally Posted by jimkingskid View Post
    OH MAN! That looks sweet. Got any other pics?
    Here's the other side, enjoy.

  4. #14
    Join Date
    May 2010
    Location
    Tampa Bay
    Age
    31
    Posts
    1,919
    Love mine. Isn't hard to install, and is pretty easy to clean once you get familiar with it. Haven't had any issues with it so far.

  5. #15
    TomCat's Avatar
    TomCat is offline Member South Carolina Riders Group
    North Carolina Riders Group
    Join Date
    Jan 2012
    Location
    Charlotte
    Age
    43
    Posts
    90
    I just put mine on, really looks sharp. I had doubts but after I got them on it was like WOW! that really dresses up the lower engine. Search around, I found them for $144 online and bought them from West End Motorsports (they will match or beat the price). Although after seeing Bills painted, I like that to, really nice looking.

  6. #16
    Join Date
    Jun 2009
    Location
    Edmond
    Posts
    50
    Quote Originally Posted by dbwhalley View Post
    I had it for about two years and it's a good looking kit. Be careful and check your clutch cable frequently. There's a sharp edge on the from Kury cover on the LH side. It wore through my clutch cable twice and so the covers are off now...
    Wow, thanks for this tip, David! I hadn't noticed this on mine but fortunately it had not worn through on mine yet. So, I just filed it down a bit (took 2 minutes) and should be good to go now.

    That being said, like everyone else I love this chrome addition, too! It goes well with their chrome frame trim covers (which I also have).

    Not to try and hijack this thread but I'm now looking at getting the Kury chrome brake and shifter covers as well as floorboard covers and rear premium floorboards. Does anyone have these and how would you rate them in relation to the engine cover?

  7. #17
    Devildoc53's Avatar
    Devildoc53 is offline Devil Doc New Mexico Riders Group
    Join Date
    Feb 2010
    Location
    Deming
    Age
    60
    Posts
    212
    Just put them on my 2007 1800T...make sure u are aware if u have aftermarket pipes they will not go on as per instructions. I have Cobra Longs on mine and it was a challenge getting them on. The back portion of the set did not sit flush on the rite side. Had to use a long screw drive and attached an allen wrench and go in from the left side to screw in to right plate. The bottom plate right plate and back plate could not go in as one piece as per instructions had to go around the pipes to piece together. Otherwise love them. Looks really good!!

  8. #18
    Join Date
    May 2012
    Location
    -
    Posts
    4
    quality is good. Metal chrome too, not any of the plastic nonsense. Only issue is if you have an aftermarket exhuast it might be a little tricky squeezing things into where they are supposed to fit.

  9. #19
    Join Date
    Apr 2008
    Location
    Windsor Ont.
    Posts
    118

    Covers

    Had to do a wack of fitting, bending and swearing to get mine on but when it was done,,,,it was chrome,,,and it was good.

  10. #20
    tomkat100's Avatar
    tomkat100 is offline Senior Member
    Missouri Riders Group
    Oklahoma Riders Group
    Join Date
    Jul 2009
    Location
    Rogers, Arkansas
    Age
    73
    Posts
    3,726
    With my dooleys, since the ignition is relocated, I had to do a little grinding and cutting, but the finished result is worth it

Page 2 of 2 FirstFirst 12

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. need to find some info on engine build up
    By speedy81304 in forum General VTX/Motorcycle Topics
    Replies: 12
    Last Post: 02-24-2011, 05:07 PM
  2. Show Chrome Engine Guards
    By BeefyBeefo in forum Honda VTX 1300 Forums
    Replies: 4
    Last Post: 07-19-2009, 10:00 PM
  3. show chrome engine guard
    By hollabaugh21 in forum Honda VTX 1300 Forums
    Replies: 0
    Last Post: 05-20-2009, 07:26 PM
  4. Kuri Chrome engine covers
    By Rico2043 in forum Honda VTX 1300 Forums
    Replies: 10
    Last Post: 07-29-2008, 11:47 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •